Volvo 740, 760, GL, GLE, GLT, Turbo Repair Manual 1982-1988

28 Mar 2015 | Author: | Comments Off on Volvo 740, 760, GL, GLE, GLT, Turbo Repair Manual 1982-1988

Volvo 740

, 760 Repair Manual 1982-1988

Usually ships the next business day

This DIY repair and service manual by Haynes, covers 1982-1988 Volvo 740 and 760 Series . 4-door sedans and 5-door station wagons, including the following models:

Volvo 740 GL

Volvo 740 GLE

Volvo 740 GLT

Volvo 740 Turbo

Volvo 760 GLE

Volvo 760 Turbo

Volvo 760 Sedans were introduced in 1982, followed by the 740 Series in 1984. 740 and 760 series cars represent the top of the Volvo range.

760 Series cars are powered by 2.8L V6 or 2.3L Turbo 4-cylinder, both fuel-injected engines. 740 Series cars are powered by 2.3L 4-cylinder engines, with or without turbocharger.

Power is transmitted to the rear wheels through a 4-speed plus overdrive manual, a 5-speed manual, a 3-speed plus overdrive automatic, or 4-speed automatic transmission.

Note: this manual DOES NOT include diesel engine information.

Book Excerpt: 1982-1988 Volvo 740, 760 Repair Manual

CLUTCH CLUTCH CABLE | ADJUSTMENT, REMOVAL AND INSTALLATION

Cable adjustment is correct when the free play at the release fork is as given in the specifications. Adjust if necessary by means of the locknuts and threaded adjuster at the end of the cable casing.

To remove the cable, loosen the adjuster as far as possible. Disconnect the return spring (if equipped) from the release fork and unhook the cable. If a rubber insulator is installed at the end of the cable, note which way it faces.

Remove the trim panel below the steering column for access to the pedals. Remove the retainer which secures the cable to the petal.

Pull the cable into the engine bay and remove it.

Install by reversing the removal operations, making sure the cable is correctly routed. Adjust the cable on completion.

CLUTCH MASTER CYLINDER | REMOVAL AND INSTALLATION

Disconnect the fluid supply hose from the master cylinder. Have a container ready to catch the fluid which will spill. Wash spilled fluid off paint immediately.

Disconnect the pressure pipe union from the end of the cylinder. Be prepared for further fluid spillage. Cover the open pipe union with a plastic bag and a rubber band to keep dirt out.

Remove the trim panel below the steering column.

Remove the clevis pin which secures the clutch pedal to the master cylinder pushrod (photo).

Remove the two nuts which secure the master cylinder to the firewall.

Remove the master cylinder, being careful not to drip fluid onto the paint.

BODY FRONT SEAT | REMOVAL AND INSTALLATION

Remove the trim or storage pocket from the outboard side of the seat base. Unbolt the seat bolt anchorage (photo).

Move the seat forwards. Remove the single bolt from the rear of each track – these may be concealed by trim covers (photo).

Move the seat rearwards. Remove any trim covers, and then remove the single bolt from the front of each track (photo).

Disconnect the seat heater, seat belt switch and adjustment motor electrical connectors (as applicable).

Lift the front of the seat, pushing it rearwards at the same time, to free the tracks from their keyhole anchors in the floor. Remove the seat and tracks together.

Install by reversing the removal operations.

REAR SEAT – REMOVAL AND INSTALLATION

SEDAN

Free the seat cushion from its retaining clips by pushing the front edge down and pulling it rearwards (photo). (On early models the clips are slightly different – Fig. 11.20. Lift out the cushion.

Straighten the tongues of the clips which secure the base of the seat back (see photo). Thump the seat back upwards to free it from the top clips and remove it.

The armrest may now be unbolted and removed if necessary.

Install by reversing the removal operations.

STATION WAGON

Fold the seat cushions forwards. Remove the hinge retaining nuts and lift out the cushions (see photo).

Fold down the seat backs. Pull the pins out of the center mounting (see photo) and release the side mounting pins by turning them with pliers. Lift out the seat backs.

Install by reversing the removal operations.

TABLE of CONTENTS:

Introduction: Vehicle identification numbers; Buying parts; Maintenance techniques, and more.

Tune-up and routine maintenance

B230 4-cylinder engine

B28 V6 engine

Engine and overhaul procedures

Cooling, heating and air-conditioning systems

Fuel and exhaust systems

Engine electrical systems

Emissions control systems

Manual transmission, overdrive

Automatic transmission, overdrive

Driveshaft

Rear axle

Brakes, ABS

Suspension and steering systems

Body

Chassis electrical system

Wiring diagrams

Subject: 1982, 1983, 1984, 1985, 1986, 1987, 1988 Volvo 740, 760 service, maintenance, repair. ISBN-10: 1850105502 | ISBN-13: 9781850105503 | Haynes 97040

PRODUCT SPECIFICATIONS:

Publisher: Haynes Manuals

Pages: 324 – Hundreds of bw photos and illustrations

Binding: Paperback – 8.5 x 11 inches

ISBN: 978-1-85010-550-3

Tagged as:

Other articles of the category "Volvo":

Twitter-news
Our partners
Follow us
Contact us
Our contacts

dima911@gmail.com

Born in the USSR

423360519

About this site

For all questions about advertising, please contact listed on the site.


Car Catalog with specifications, pictures, ratings, reviews and discusssions about cars