2013 Kia Rio Accessories | etrailer.com

23 Jan 2015 | Author: | Comments Off on 2013 Kia Rio Accessories | etrailer.com
Kia Rio

2013 Kia Rio Videos

Today on this 2013 Kia Rio, were going to do a test fit of part number rx5079281 from Rain-X. This is their latitude windshield wiper blade. A couple things to know about this part, it is designed for use in rain, snow, and sleet. It has a beam style construction that applies the even pressure across the entire length of the blade. It also has an aerodynamic design to help reduce wind drag and noise and lift.

The rubber squeegee has built in UV inhibitors to help protect it from the sunlight.

Today on this 2013 Kia Rio, were going to do a test fit of part number rx30226 from Rain-X; this is our weather beater windshield wiper blade. A couple things to know about this wiper blade is that it is a frame styled design for multiple pressure points to give it even pressure across the windshield. Its built from a galvanized steel frame to help stand up to the elements and the rubber edge also has built in UV inhibitors to help protect it from the sunlight.

Well go ahead and start off our test fit by removing the original wiper blade. Theres a small tab that we have to push to release it and then go ahead and slide it off the arm. Our arms a J-style, so it will be easy install the new blade.

Today on this 2013 Kia Rio, well be test fitting the Yakima Quickback 2-Bike Carrier, part number Y02621.To begin our test fit well set the carrier onto the trunk with the cradle arms towards the top of the trunk mount facing outward. Well then use the straps at the top of the carrier to hook to the top of the trunk and then straps towards the bottom of the carrier to hook to the bottom of the trunk and then pull the straps tight to secure the carrier in place.Once the carrier is tightened in place you can fold out the access strap and place it in a black clip.To load the bike, first, make sure that the cradle arms are level or at a level bit of an angle facing up then undo the cradle straps. Set the bike onto the frame cradles and secure with the cradle straps.That concludes todays test fit for the Yakima Quickback 2-Bike Carrier, part number Y02621 on this 2013 Kia Rio.

Today on this 2013 Kia Rio, well be test fitting the Yakima King Joe Pro 2-Bike Carrier, part number Y02624.To begin our test fit, well set the carrier onto the trunk and use the grey dials located at each end of the carrier to adjust it to fit it correctly. Once you have determined appropriate setting for the vehicle take the straps at the top of the carrier and hook it to the top of the trunk and again the straps at the bottom of the carrier to the bottom of the trunk and pull them tight to secure it tightly to the trunk.Once the carrier fits snug against the trunk you can open up the right handles located at the inside center of the carrier to pull their cradle arms out then push the red handle back in to secure it.To load the bike, undo the cradle straps, set the bike onto the frame cradles and secure it again with the cradle straps.That concludes todays test fit for the Yakima King Joe Pro 2-Bike Carrier, part number Y02624 on our 2013 Kia Rio.

2013 Kia Rio Questions and Answers

Kia Rio

When the Draw-Tite trailer hitch # 24883 is installed on a 2013 Kia Rio only the receiver will show at the bottom of the vehicle. The cross member will be hidden. The hitch is designed with the receiver welded to the bottom of the cross member so the rest of the hitch is hidden.

I have included a diagram from the instructions to give you a better idea if what this will look like. If you are planning on doing some towing use the following parts to complete your towing set up: Ball mount # 3

Yes, the Curt Custom Fit Wiring Harness, # C56175, is the correct wiring harness for your 2013 Kia Rio EX Sedan ECO. This wiring harness will splice into the vehicle wiring behind the tail light assemblies. I have attached a link to the installation instructions for you to check out.

The anti-rattle knob on the Thule Apex, # TH9025, can be tricky. The key is that the rack has to be in the hitch and the knob has to be unlocked and tightened down as much as you can by hand. Then when you lock the knob, the knob should just spin and not be able to loosen or tighten.

I made a video showing this for you to view.

For your 2013 Kia Rio 5-Door and the Rhino Rack roof rack, there are numerous basket options that will fit. Depending on the size you want here are the options: 46 inches long by 34 inches wide, # RLBS-U. Based on the vehicle I recommend this basket. We also have these sizes: 61 by 45 inches, # RLBL-S280 48 by 38 inches, # RLBM-U 56 by 23 inches, # RLBH-U

Kia Rio
Kia Rio
Kia Rio
Kia Rio
Kia Rio
Kia Rio
Kia Rio
Kia Rio
Tagged as:

Other articles of the category "Kia":

Twitter-news
Our partners
Follow us
Contact us
Our contacts

dima911@gmail.com

Born in the USSR

423360519

About this site

For all questions about advertising, please contact listed on the site.


Car Catalog with specifications, pictures, ratings, reviews and discusssions about cars