2011 Nissan Xterra Accessories | etrailer.com

4 Aug 2014 | Author: | Comments Off on 2011 Nissan Xterra Accessories | etrailer.com
Nissan Xterra

2011 Nissan Xterra Accessories

2011 Nissan Xterra Videos

Today we have a 2011 Nissan Xterra and we will be installing the Tow Ready T-One Connector Part Number 118525. After removing the contents from the package, you will notice you have three relays. These three relays need to be plugged in to the jumper wire also included in the packaging. After plugging the three relays in, we are now ready to move inside the vehicle. Here on the passenger side, we will need to remove the passenger side kick panel.

To do this, we will first need to remove the passenger side floor seal by pulling upwards on the floor seal and then out towards the rear of the vehicle.

Today on this 2011 Nissan Xterra we are going to be installing Curt hitch part number 13514. Before we get started with the installation we are going to show you a couple of final installed dimensions that are going to help make choosing your hitch accessories a little bit easier. From the top of the receiver tube opening to the ground is going to measure 18 inches.

From the center of the pin hole to clear the rear edge of the bumper is going to measure approximately two inches. Now we will move on to the installation. 00:25

Today on this 2011 Nissan Xterra we are going to be installing the modulite wiring harness part number 119176KIT. We are going to start the installation off underneath the vehicle and the Xterra is a little unique in that it has a partial tow package already installed on it so we are actually going to use the wires for that to install the modulite kit.

Come over to the driver side of the vehicle near the bumper area and follow the frame forward to locate this open ended port right here and this is the tow package port so what I am going to do is pull it off of its retaining clips to give me a little bit more work room. What I have done is cut back some of the tape already to expose the wires. 00:44

2011 Nissan Xterra Questions and Answers

For your 2011 Nissan Xterra with a 2 inch hitch you could get a Thule Vertex 2 Bike Carrier # TH9028 like you referenced. This is a quality rack that has anti-sway cradles, a locking anti-rattle device and a tilt feature to allow access to the rear cargo area. I attached a review video for you to check out.

The most popular bike rack among 2011 Nissan Xterra owners that we sell is the Thule T2 Platform Rack # TH916XTR. This is a platform rack that allows the bikes to sit in a tray and an arm

The Rhino-Rack crossbars in roof rack # SXBS9 are 3-1/8 inches wide, the same as the Rola bars, so the Rola cargo basket will fit on the Rhino-Rack bars. The bars will need to be spaced a center distance apart on center to accommodate the basket. There are 4 possible crossbar spreads that will work: 26-1/4 inches, 30 inches, 33-3/4 inches, or 37-1/2 inches.

You will just need to place the crossbars to match one of these 4 bar spreads. The widest, 37-1/2 inches, would be the best. I have incl

The rails of the Tow Ready Hitch Cargo Carrier, item # 63153, are 5-1/2 inches tall and the shank on the carrier raises it 2-1/2 inches. Adding these together you get 8 inches of rise from the top of the receiver opening. To determine if the cargo carrier will allow the rear door to open on your Xterra you will need to do some measuring.

Measure from the lowest part of the rear door straight down to the top of the receiver opening. If this measurement is 8 inches or more you will be able to use

To add a 7-Way trailer connector and a brake controller you will need # ETBC7 and the brake controller itself. Since your 2011 Nissan Xterra did not come with a factory 7-Way, a brake controller will need to be hardwired in. The ETBC7 kit comes with everything you will need, minus the brake controller, to set the vehicle up properly.

Since at most you will have 4 brake assemblies you will use the 20 amp circuit breaker that is included with the ETBC7. The 30 amp one will not be used and the

Nissan Xterra

In order for the CURT Cargo Basket, # C18115, to fit your 2011 Nissan Xterra factory crossbars, they would have to be under 3 inches in diameter and have a crossbar spread, center to center, of at least 15 inches. If the crossbars are greater than 3 inches in diameter, you would need to add the Thule Crossroads Roof Mounted Roof Railing Foot Pack, # TH450, and 50 inch load bars, # THLB50.

You are correct. I checked with Yakima and in order to use the BasketCase, # Y07012, on your 2011 Nissan Xterra factory crossbars, you will need the Universal MightyMounts, # Y03590. I have included a link to the installation details for the MightyMounts and the BasketCase for you.

For a cargo net, use the Stretch Net for Yakima BasketCase, # Y07011.

All of the trailer hitches available for a 2011 Nissan Xterra are going to be Class III trailer hitches. This is good because that is exactly what I would recommend. A Class III trailer hitch is going to give you plenty of gross trailer weight capacity and the 2 inch receiver will allow you more options for accessories like bike racks and cargo carriers.

Basically, all 3 of the available hitches for your vehicle install in the same way. If you are looking to save a little money, go with the C

I spoke with my contact at Tekonsha and she informed me that the Tekonsha Brake Controller Harness, part # 3050-P that you referenced will work on your 2011 Nissan Xterra to allow you to connect your brake controller to the 7-way wiring that is on your vehicle. The harness will be located underneath and left of the steering column, taped to another harness near the emergency brake pedal. It is a 6-pin connector that mates with the 3050-P brake control wiring adapter. If you need a brake c

Yes, you will need the Thule Xadapt3, # THXADAPT3, M6 bolts for attachment of the Thule Ride-On Adapter, item # TH532, to the factory load bars on your 2011 Nissan Xterra.

The Thule Domestique Fork-Mount Bike Carrier – Roof Mount, part # TH513, will attach to the factory roof rack crossbar on your 2011 Nissan Xterra. If you do not have room to store the front wheel of your bike inside the vehicle, you can use the Thule Wheel-On Roof Mounted Bike Wheel Carrier, part # TH593. The wheel carrier adds a place for you to attach the front wheel of your bike to your roof rack. If you are needing to lock the bike to the bike carrier and lock the carrier to the cross

Nissan Xterra
Nissan Xterra
Nissan Xterra
Nissan Xterra
Nissan Xterra
Nissan Xterra
Nissan Xterra
Tagged as:

Other articles of the category "Nissan":

Twitter-news
Our partners
Follow us
Contact us
Our contacts

dima911@gmail.com

Born in the USSR

423360519

About this site

For all questions about advertising, please contact listed on the site.


Car Catalog with specifications, pictures, ratings, reviews and discusssions about cars