2008 Kia Sorento Accessories | etrailer.com

26 Oct 2014 | Author: | Comments Off on 2008 Kia Sorento Accessories | etrailer.com

2008 Kia Sorento Videos

Today on our 2008 Kia Sorento we#39;ll be installing Hidden Hitch, part number 87425. This is what our hitch will look like once it#39;s installed. Next we#39;ll go ahead and give you a couple of measurements to assist your selecting accessories for your new hitch such as a ball mount, bike rack or cargo carrier. The center of the hitch pin hole is even with the outermost edge of the bumper. The top of the receiver tube opening to the ground is 14 inches.

Now we#39;ll go ahead with installation.

Today on our 2008 Kia Sorento we#39;ll be installing the Draw-Tite hitch, part number 75516. This is what our hitch will look like once it#39;s installed. Next we#39;ll go ahead and give you a couple of measurements to assist your selecting accessories for your new hitch such as a ball mount, bike rack or cargo carrier.The center of the hitch pin hole is even with the outermost edge of the bumper.

The top of the receiver tube opening to the ground is 14 inches. Now we#39;ll go ahead with installation. To begin our install we#39;ll first point out the attachment points.

Today on our 2008 Kia Sorento we#39;ll be installing the Curt Hitch, part number c13513. This is what our hitch will look like once its installed. Next we#39;ll go ahead and give you a couple of measurements to assist your selecting accessories for your new hitch such as a ball mount, bike rack or cargo carrier.From the center of the hitch pin hole to the outermost edge of the bumper is 1-1/2 inches. From the top of the receiver tube opening to the ground is 14-1/2 inches.

Now let#39;s go ahead with the installation. To begin our install we#39;ll first point out the attachment points.

Today, on our 2008 Kia Sorento, we#39;ll be adding the adapter four-pole to seven-pole with test lamps, part number C57674. After this application, we#39;ll only be connecting the ground running lights and turn signals. To begin our install, we#39;ll first mount the seven-pole the bracket onto the seven-pole connector.

We#39;ll use the hardware provided with the seven-pole kit.Now, for this application, we#39;ll only be using the four-pole connector, so were going to go ahead and fold under the extra wiring and tape it up to clean up our install look. Now, with that done, we#39;ll go ahead and add the Draw Tite no-drill mounting bracket, part number 18136. Once secured, we#39;ll attach the no-drill mounting bracket to the hitch using the worm clamp provided.Now, with that secured, we#39;ll go ahead and route the seven-pole wiring up over the hitch and secure it to the fourth pole connector already on the vehicle.

2008 Kia Sorento Questions and Answers

The Tow Ready wiring harness # 118269 is designed to fit a 2008 Kia Sorento that came with the factory tow package. You can have the dealer run the VIN to determine if your Sorento was equipped with a factory tow package. If it was not then you would need to use a hard wire harness, # 119147KIT.

If it does have the factory tow package then there is most likely a bad ground causing the problem or, if the vehicle uses relays for its tow package wiring, a bad relay. Relays can be obtained from a

If your 2008 Kia Sorento comes with a factory tow package, I recommend the Curt Wiring Harness # C56151. This harness has two connectors on it with one using the existing factory-installed harness to obtain 12-volt power from the battery and the other providing the lighting signals. If it does not, the Curt Wiring Harness # 56146KIT you made reference to will work. This connector will need to be hardwired into the existing wiring using the supplied circuit tester to find the proper circuits t

Yes, the Curt trailer hitch # C13513 is a confirmed fit for a 2008 Kia Sorento.

I have included a link to the installation instructions for you and a link to a video showing a typical installation. It is on a 2005 model but installation will be very similar to your 2008 model. If you plan on doing some towing, I recommend the etrailer ball mount kit # 989900. It comes with 2 ball mounts, 2 balls, a hitch pin with clip, and a carrying bag.

For trailer wiring use # 56146KIT. I have included a l

The Bulldog Replacement Heavy-Duty Caster, # BDCP555 is indeed compatible with the Bulldog # BD155022 jack that you have. Keep in mind that the capacity of the jack will be decreased to 1500 lb when using the caster. Since the jack only needs to support the tongue weight of the camper and not the entire weight, this should not prove to be a problem with a pop-up camper.

There could be several issues that are causing the trailer light problem you are experiencing and I can help you troubleshoot. First, we need to determine if the problem is on the vehicle side or the trailer side. You can start by testing the vehicle side 4-Way trailer connector. using a circuit tester like # 3808, test the pins on the vehicle side 4-Way for the proper functions.

If they are working properly then you know the problem is on the trailer side. If they are not working correctly,

Tagged as:

Other articles of the category "Kia":

Twitter-news
Our partners
Follow us
Contact us
Our contacts

dima911@gmail.com

Born in the USSR

423360519

About this site

For all questions about advertising, please contact listed on the site.


Car Catalog with specifications, pictures, ratings, reviews and discusssions about cars